GYS Series Hydraulic Cone Crusher is a new kind of cone crusher, which combines the single-cylinder hydraulic cone crusher with the ordinary cone crusher and adopts advanced design concept and optimized design. Better crushing frequency and eccentricity are used, so the content of the fine grains is higher in crushing products. It can significantly improve the processing ability of the follow-up process, reduce the overall energy consumption.
The crushing chamber of GYS hydraulic cone crusher is divided into four cavities according to the crushing size requirement. They are medium crushing, medium and fine crushing, fine crushing and super fine crushing.
It is suitable for crushing materials with Platts hardness f = 5-16, such as iron ore, nonferrous metal ore, granite, limestone, quartzite, sandstone, pebbles, etc, these ores and rocks are widely used in metal mining, metallurgical industry, chemical industry, construction industry, cement and sand industry, etc. It is the ideal equipment for large stone plants and mining crushing.
GYS series hydraulic cone crusher consists of the transmission shaft, eccentric sleeve, ball bearing, hydraulic insurance device, adjusting ring, pulley, frame and other components.
large handling capacity, good grain size; The type of crushing chamber with high performance and high crushing frequency, greatly improving the processing capacity of the machine, because of the use of laminated crushing principle, most of crushing products are cubic structure and greatly reduce the needle flake.
Low failure in operation; Due to the optimized design and hydraulic protection, the fewer breakdowns happen, and the fault-free operation ratio will exceed 85% in normal use.
Easy to operate and maintain; It is convenient to adjust the discharge port, save time and energy, especially the lining board is easy to change quickly, reducing the downtime.
The full hydraulic operation, strong automation; It can increase the reliability of the machine operation and greatly improve the service life.
The crushing cavity type can be assembled in a variety of combinations, which is better fit the special requirements of users.
large end of
crushing cone (mm)
Adjusting Range of
Discharge Opening (mm)
Feed Opening Size
of the Opening
Edge when Recommending
Min. Discharging Gate Opening (mm)
Main motor power
|FTMGYS 300||C1||910||13~38||175||150||81~180||6P 90||10|
|FTMGYS 400||C1||1200||19~51||241||205||207~400||6P 200||20|
|FTMGYS 500||C3||1600||25~64||269||228||280~650||6P 280||40|
|FTMGYS 700||C1||2000||31~64||369||314||1125~1814||6P 480||90|
Leave a Message
Here you can submit any questions and we will get back to you as soon as possible. We will not disclose the information you submit to anyone, please rest assured.
Common Senses on Lubrication System of Symons Crushers
Common senses on lubrication system of symons crushers,1. Lubricating oil enters the symons crushers in two ways.2. Keep the lubricating oil warm in winter.3. Lubricating oil temperature shall not be higher than 60 ℃.4. Control oil pressure.5. The limit of water which entering the heat exchanger.6. Conduit cleaning of the lubrication system.7. Oil level in the oil receiver.8. Keep the filter clean.9. Inspection frequency.
Advantages and Disadvantages of CS Cone Crusher and HP Cone Crusher
Advantages and disadvantages of cs cone crusher( single cylinder hydraulic cone crusher).Advantages and disadvantages of hp cone crusher(multi-cylinder hydraulic cone crusher).
The Ore Is Precious Please Cherish
Why is the ore expensive?1.Ore mining is not only difficult but also expensive.2. Ore is a one-time energy that cannot be regenerated.3. Mining will bring environmental pollution that is difficult to repair.How are the mineral resources wasted?1.The mining machinery was used improperly.2. Tailings treatment is imperfect.
Notes for the lubrication of cone Crusher
Cone crusher is an important equipment for the stone pit. According to incomplete statistics, the mechanical failure of the cone crusher due to improper lubrication is as high as 30% of all faults.
Contrastive Analysis of Cone Crushers and Jaw Crushers
Contrastive analysis of cone crushers and jaw crushers.1.Category description of cone crushers and jaw crushers.2.Structural description of cone crushers and jaw crushers.3. Operating principle of cone crushers and jaw crushers.4.Applicable materials of cone crushers and jaw crushers. 5.Crushing capacity of cone crushers and jaw crushers.
HP Series Bauxite Cone Crusher Delivered to Brazil
Today, one HP200 bauxite hydrocone crusher with the productivity of 3000 tons per day has been packaged already and will be shipped to Brazil.